Home › Bosch error codes › Error code E115

Bosch Oven Error Code E115

Call a professionalReviewed November 2026Checked against manufacturer documentation
What this code means
E115: Temperature in the unlocked cavity too high (upper or single cavity)

E115 is a safety response: the upper (or only) cavity got hotter than allowed while its door was unlocked, so the oven stops heating and locks the door until things cool down. A welded relay or a lying sensor is behind it, which makes it professional work.

Also shown as: E215

Fix level
Call a professional
The checks on this page are preliminary. The likely fix involves a part, wiring or the control board.
Time to run the checks
About 20–40 minutes
For the 4 checks on this page — not a full repair.
You may need
No special tools
The checks below use basic household items only.
Parts that may be involved
Power board (relay board), Oven temperature sensor
Parts are model-specific; see the note below before ordering.

Common causes

  1. Heating relay stuck on, heating an unlocked cavity
  2. Temperature sensor misreading low
  3. Control module failure (the manual's own listed causes centre on the control and sensors)

What to check, in order

Safety first. Switch the appliance off and unplug it before checking anything inside it. If you are not comfortable with any step, stop and call a technician.
  1. Switch the oven off at the breaker and leave it off; the control responds to E115 by stopping heat and locking the door, but a stuck relay can defeat that.
  2. Let the oven cool; once the temperature falls into the allowed range the latch unlocks and the error clears by itself.
  3. Do not use the oven again until it has been checked — uncontrolled heating in an unlocked cavity is exactly what this code exists to catch.
  4. Book a technician to test the relay board and sensor. E215 is the lower-cavity version on double ovens.

Clear the code and test

  1. Fix what the checks above found first. Clearing the code without fixing the cause only brings it back.
  2. Plug the appliance back in and restore its water supply if it has one.
  3. Run the shortest programme and watch the point where the code appeared before.
  4. If the programme finishes with no code, the fault is cleared. If the code returns, write it down before calling a technician — it speeds up the diagnosis.

When to call a professional

This code usually points to a faulty part, wiring or the control board on a Bosch oven. Run the checks above to rule out the simple causes, then book a technician — and book one straight away if any of these apply:

  • The code comes back after you have run the checks and a test cycle.
  • You smell burning, see sparks or scorch marks, or the breaker trips.
  • Water is leaking and you cannot stop it at the tap.
  • The fix needs panels opened beyond what your manual describes, or a part tested with a meter, and you are not set up for that.

When you call, give the brand, the code E115, your model number (on a label inside the door or on the back) and the checks you already ran. It shortens the visit.

Repair or replace?

This fault is in professional territory: the fix usually means a major part or board-level work, and the labour adds up. If your machine is already well into its service life, get the repair quote first, then compare it with the price of a current equivalent model before you decide. Paying a large share of a new machine's price to repair an old one is rarely the better deal; replacing a machine over one cheap fault is wasteful too.

Parts that may be involved

Power board (relay board)Oven temperature sensor

Parts are model-specific. Find your model number first — usually on a label inside the door, on the door frame or on the back — and match the part to that number before ordering.

Questions people ask about E115

What does E115 mean on a Bosch oven?

E115 means: Temperature in the unlocked cavity too high (upper or single cavity). E115 is a safety response: the upper (or only) cavity got hotter than allowed while its door was unlocked, so the oven stops heating and locks the door until things cool down. A welded relay or a lying sensor is behind it, which makes it professional work.

Can I fix Bosch E115 myself?

Only the preliminary checks. Code E115 usually means a part, wiring or the control board has failed, which is a technician job. Run the checks to rule out simple causes before you book.

How do I clear Bosch E115?

Fix the cause first — clearing the code on its own brings it straight back. Then restore power and water, run the shortest programme, and watch the stage where the code appeared. If the programme finishes with no code, it is cleared.

Sources checked

The meaning and checks for this code were checked against the sources above in November 2026. Codes vary by model and region; if your manual lists a different meaning for your exact model, follow the manual.

Other Bosch oven codes

Bosch E000Wrong module combination — control module and user interface are mismatchedBosch E005Communication error between user interface and control moduleBosch E009ROM check error in the user interfaceBosch E010Data memory error in the user interfaceBosch E011One key pressed continuously (key held for 10 seconds or more)Bosch E032Multiple keys pressed continuouslyBosch E101Cavity temperature sensor open circuit (upper or single cavity)Bosch E104Cavity temperature sensor shorted (upper or single cavity)Bosch E106Door latch does not lock (upper or single cavity)Bosch E107Door latch does not unlock (upper or single cavity)Bosch E116Meat probe error — probe connection unstable or shortedBosch E118Cooling fan supervision error — fan speed too low or too highBosch E122Meat probe sensor temperature too high or shortedBosch E123Meat probe sensor temperature too lowBosch E126Door latch error — latch position switch signals lostBosch E302Control module too hot — electronics over temperatureBosch E303Electronics temperature too high or rising too fast (control module)Bosch E309ROM check error in the control moduleBosch E310Data memory error in the control moduleBosch E312Defective control module temperature sensorBosch F111Runaway oven temperature (upper or single oven)Bosch F113Runaway oven temperature at the higher limit (upper or single oven)Bosch F121Stuck key on the touch control panelBosch F125Cancel key circuit problem (upper or single oven)Bosch F141Slave microprocessor not functioningBosch F151EEPROM failure or communication circuit errorBosch F153Control calibration values out of rangeBosch F155Corrupted EEPROMBosch F31Oven temperature sensor failure (upper or single oven)Bosch F32Lower oven temperature sensor failureBosch F33Warming drawer temperature sensor defectiveBosch F41Oven door latch will not lock (upper or single oven)Bosch F42Lower oven door latch will not lockBosch F43Oven door latch will not unlock (upper or single oven)Bosch F44Lower oven door latch will not unlockBosch F45Oven door latch switches defective — latch reads locked and unlocked at the same time