Home › Bosch error codes › Error code E26

Bosch Dishwasher Error Code E26

Call a professionalReviewed November 2026Checked against manufacturer documentation
What this code means
E26: Water switch (diverter) motor fault

The motorised water switch that directs flow between the spray arms cannot move to its positions, so washing stops or only part of the load gets sprayed. A sliver of glass can jam the mechanism, but the switch sits under the tub and is not a user-serviceable part. Expect a technician to test the diverter motor and its circuit.

Fix level
Call a professional
The checks on this page are preliminary. The likely fix involves a part, wiring or the control board.
Time to run the checks
About 15–30 minutes
For the 3 checks on this page — not a full repair.
You may need
No special tools
The checks below use basic household items only.
Parts that may be involved
Diverter motor (water switch), Main control board (+1 more below)
Parts are model-specific; see the note below before ordering.

Common causes

  1. Failed diverter (water switch) motor
  2. Glass or debris jamming the water switch
  3. Wiring fault to the diverter
  4. Control board output fault

What to check, in order

Safety first. Switch the dishwasher off and unplug it (or turn off its breaker) before checking hoses or filters. Expect water in the bottom of the tub and around the filter; keep a tray and towel ready. If you are not comfortable with any step, stop and call a technician.
  1. Clean the filter and check the sump for glass or debris that could have entered the mechanism.
  2. Reset power at the breaker for 30 seconds and run a short cycle.
  3. If the code returns, book a technician to test the diverter motor.

Clear the code and test

  1. Fix what the checks above found first — a filter cleaned, a hose straightened, the spray arms freed. Clearing the code without fixing the cause only brings it back.
  2. Close the door, plug the dishwasher back in (or restore its breaker) and make sure the water tap is open.
  3. Run the shortest programme and stay nearby for the first minutes, watching for leaks and listening for the drain pump.
  4. If the programme finishes with no code, the fault is cleared. If the code returns, write down the code and when it appeared before calling a technician — it speeds up the diagnosis.

When to call a professional

This code usually points to a faulty part, wiring or the control board on a Bosch dishwasher. Run the checks above to rule out the simple causes, then book a technician — and book one straight away if any of these apply:

  • The code comes back after you have run the checks and a test cycle.
  • You smell burning, see sparks or scorch marks, or the breaker trips.
  • Water is leaking and you cannot stop it at the tap.
  • The fix needs panels opened beyond what your manual describes, or a part tested with a meter, and you are not set up for that.

When you call, give the brand, the code E26, your model number (on a label inside the door or on the back) and the checks you already ran. It shortens the visit.

Repair or replace?

This fault is in professional territory: the fix usually means a major part or board-level work, and the labour adds up. If your machine is already well into its service life, get the repair quote first, then compare it with the price of a current equivalent model before you decide. Paying a large share of a new machine's price to repair an old one is rarely the better deal; replacing a machine over one cheap fault is wasteful too.

Parts that may be involved

Diverter motor (water switch)Main control boardWiring harness

Parts are model-specific. Find your model number first — usually on a label inside the door, on the door frame or on the back — and match the part to that number before ordering.

Questions people ask about E26

What does E26 mean on a Bosch dishwasher?

E26 means: Water switch (diverter) motor fault. The motorised water switch that directs flow between the spray arms cannot move to its positions, so washing stops or only part of the load gets sprayed. A sliver of glass can jam the mechanism, but the switch sits under the tub and is not a user-serviceable part. Expect a technician to test the diverter motor and its circuit.

Can I fix Bosch E26 myself?

Only the preliminary checks. Code E26 usually means a part, wiring or the control board has failed, which is a technician job. Run the checks to rule out simple causes before you book.

How do I clear Bosch E26?

Fix the cause first — clearing the code on its own brings it straight back. Then restore power and water, run the shortest programme, and watch the stage where the code appeared. If the programme finishes with no code, it is cleared.

Sources checked

The meaning and checks for this code were checked against the sources above in November 2026. Codes vary by model and region; if your manual lists a different meaning for your exact model, follow the manual.

Other Bosch dishwasher codes