Home › Beko error codes › Washing Machine › Error code E04

Beko Washing Machine Error Code E04

DIY-friendlyReviewed November 2026Checked against manufacturer documentation
What this code means
E04: Fill fault — the machine is not filling with water in the allowed time

The machine is filling too slowly or not at all. Work through the water supply first: most fill faults are a closed tap, a kinked hose or a clogged inlet filter rather than a failed part.

Also shown as: E4

Applies to: Beko washing machines and washer-dryers with a display, older WMA to WMG era models

Fix level
DIY-friendly
Most people can run the checks on this page with basic household items.
Time to run the checks
About 25–50 minutes
For the 5 checks on this page — not a full repair.
You may need
No special tools
The checks below use basic household items only.
Parts that may be involved
Water inlet valve, Inlet hose (+1 more below)
Parts are model-specific; see the note below before ordering.

Common causes

  1. Water tap closed or only partly open
  2. Kinked or trapped inlet hose
  3. Blocked mesh filter in the inlet valve
  4. Low mains water pressure
  5. Failed inlet valve solenoid

What to check, in order

Safety first. Switch the machine off and unplug it before cleaning filters or moving hoses. Expect water to come out when you open a pump filter; keep a tray and towel ready. If you are not comfortable with any step, stop and call a technician.
  1. Confirm the water tap behind the machine is fully open.
  2. Straighten the inlet hose and make sure nothing heavy is resting on it.
  3. Turn off the tap, unscrew the inlet hose at the machine and clean the small mesh filter inside the connection.
  4. Check another tap in the house runs at normal pressure.
  5. If the supply is good and E04 returns, the inlet valve needs testing — a technician job.

Clear the code and test

  1. Fix what the checks above found first — a filter cleaned, a hose straightened, taps opened. Clearing the code without fixing the cause only brings it back.
  2. Close the door, plug the machine back in and restore the water supply.
  3. Run a short rinse and spin, or the shortest wash programme, and watch the stage where the code appeared before (filling, washing, draining or spinning).
  4. If the cycle finishes with no code, the fault is cleared. If the code returns at the same stage, write down the code and that stage before calling a technician — it speeds up the diagnosis.

When to call a professional

Most cases are solved by the checks above. Book a technician if any of these apply:

  • The code comes back after you have run the checks and a test cycle.
  • You smell burning, see sparks or scorch marks, or the breaker trips.
  • Water is leaking and you cannot stop it.
  • The fix needs panels opened beyond what your manual describes, or a part tested with a meter, and you are not set up for that.

When you call, give the brand, the code E04, your model number (on a label inside the door or on the back) and the checks you already ran. It shortens the visit.

Parts that may be involved

Water inlet valveInlet hoseMesh filter

Parts are model-specific. Find your model number first — usually on a label inside the door or on the back — and match the part to that number before ordering.

Questions people ask about E04

What does E04 mean on a Beko washing machine?

E04 means: Fill fault — the machine is not filling with water in the allowed time. The machine is filling too slowly or not at all. Work through the water supply first: most fill faults are a closed tap, a kinked hose or a clogged inlet filter rather than a failed part.

Can I fix Beko E04 myself?

Usually, yes. Code E04 is rated DIY-friendly: the checks on this page cover the common causes and use basic household items only. If the code returns after the checks and a test cycle, book a technician.

How do I clear Beko E04?

Fix what the checks above found first — a filter cleaned, a hose straightened, taps opened. Clearing the code without fixing the cause only brings it back. Close the door, plug the machine back in and restore the water supply. Run a short rinse and spin, or the shortest wash programme, and watch the stage where the code appeared before (filling, washing, draining or spinning).

Sources checked

The meaning and checks for this code were checked against the sources above in November 2026. Codes vary by model and region; if your manual lists a different meaning for your exact model, follow the manual.

Other Beko washing machine codes

Beko E01Door lock fault — the machine cannot confirm the door is closed and lockedBeko E02Heating fault — the water is not reaching the set temperatureBeko E03Drain fault — the machine cannot empty the water in the allowed timeBeko E05Pressure switch fault — the water level sensor is reading incorrectlyBeko E06NTC thermistor fault — the temperature sensor is not reading correctlyBeko E07Motor circuit fault — the motor or its control triac has failedBeko E08Motor tachometer fault — the control board cannot read the drum speedBeko E13Water leak detected — the anti-flood system has found water in the baseBeko H1NTC thermistor open or short circuit (service test code)Beko H11Motor or tachogenerator open circuit (service test code)Beko H2Heater open circuit (service test code)Beko H3Heater stuck on — heater triac or relay shorted (service test code)Beko H4Inlet valve triac short circuit (service test code)Beko H5Drain pump open circuit (service test code)Beko H6Motor triac short circuit (service test code)Beko H7Pressure sensor failure (service test code)Beko H8Tachometer fault — motor speed sensor (service test code)

See all Beko washing machine error codes